Diferencia entre revisiones de «UDPSendReceiveString»

#include <Ethernet.h>
#include <EthernetUdp.h>

byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };         //Asignar MAc al modulo
IPAddress ip(192, 168, 1, 177);                              //Asignar IP
unsigned int localPort = 8888;                               //Asignar puerto a escuchar

// buffers for receiving and sending data
char packetBuffer[UDP_TX_PACKET_MAX_SIZE];  // buffer to hold incoming packet,
char ReplyBuffer[] = "acknowledged";        // a string to send back

EthernetUDP Udp;             //Instanciar UDP
byte CS = 10;               //Confugura CS para UNO
//byte CS = 15;               //Confugura CS para ESP8266
//byte CS = 33;               //Confugura CS para ESP32
//byte CS = 5;               //Confugura CS para MKR

void setup() {
   Serial.begin(9600);
   Ethernet.init(CS);
   Ethernet.begin(mac, ip);        //Iniciar Ethernet

   // Check for Ethernet hardware present
   if (Ethernet.hardwareStatus() == EthernetNoHardware) {
      Serial.println("Ethernet shield was not found.  Sorry, can't run without hardware. :(");
      while (true) {
         delay(1);     //do nothing, no point running without Ethernet hardware
      }
   }
   if (Ethernet.linkStatus() == LinkOFF) {
      Serial.println("Ethernet cable is not connected.");
   }
   Udp.begin(localPort);   //Inicializa UDP
}

void loop() {
   // if there's data available, read a packet
   int packetSize = Udp.parsePacket();
   if (packetSize) {
      Serial.print("Received packet of size ");
      Serial.println(packetSize);
      Serial.print("From ");
      IPAddress remote = Udp.remoteIP();
      for (byte i=0; i<4; i++) {
         Serial.print(remote[i], DEC);
         if (i < 3) {
            Serial.print(".");
         }
      }
      Serial.print(", port ");
      Serial.println(Udp.remotePort());

      // read the packet into packetBufffer
      Udp.read(packetBuffer, UDP_TX_PACKET_MAX_SIZE);
      Serial.println("Contents:");
      Serial.println(packetBuffer);
      // send a reply to the IP address and port that sent us the packet we received
      Udp.beginPacket(Udp.remoteIP(), Udp.remotePort());
      Udp.write(ReplyBuffer);
      Udp.endPacket();
   }
   delay(10);
}

 // Processing UDP example to send and receive string data from Arduino
 // press any key to send the "Hello Arduino" message


import hypermedia.net.*;
UDP udp;  // define the UDP object

void setup() {
   udp = new UDP( this, 6000 );  // create a new datagram connection on port 6000
   //udp.log(true); 		 // <-- printout the connection activity
   udp.listen(true);             // and wait for incoming message
}

void draw() {
   //Nada
}

void keyPressed() {
   String ip = "192.168.1.177"; 	 // the remote IP address
   int port = 8888;		         // the destination port
   udp.send("Hello World", ip, port );   // the message to send
}

void receive( byte[] data ) { 			// <-- default handler
   //void receive( byte[] data, String ip, int port ) {	// <-- extended handler
   for (byte i=0; i<data.length; i++)
      print(char(data[i]));
      println();
   }
}